Bad Ass Cars

Why does my engine still try to run after I shut it off?

Why does my engine still try to run after I shut it off?

How to stop engine run-on or "Dieseling".

This is a common problem that can be caused by a couple of things. Some people call this "dieseling" or engine "run-on". What is happening is; when you shut the ignition off, something, somehow is causing a couple of the cylinders to keep igniting, which in turn keeps the engine running, although "sputtering" pretty badly. This can be caused by excessive carbon build-up in the combustion chambers or on the piston tops which when hot it'll act like glow plugs and will ignite a little bit of fuel getting into the cylinders. This is common on engines that run way too rich or have oil burning problems.

Dieseling is a common problem with high compression / high performance engines, especially in warm weather or when the engine is hot. In this case, it's usually caused by running "cheap" gas with inadequate octane because cheap, low octane gas is actually more volatile than higher octane / better fuel. In this case it can usually be remedied by switching to a higher octane fuel.

In milder street engines, another big cause for engine run-on is having the idle set too high, or the carb is mis-adjusted, which requires the idle speed screw to be screwed-in too far to get the engine to idle. When the idle speed screw is in too far, it opens the throttle plates too wide and the engine will actually pull some fuel through the main jets a little, so when you shut the engine off, the inertia of the spinning engine still pulls air (and some fuel) through the carb and into the cylinders. The heat built-up inside the combustion chambers is enough to light a few of the cylinders at random to keep the engine spinning and sputtering. Again, this is especially true with fuel that isn't high enough in octane. The more the octane, the less volatile the fuel is.

how to stop engine run on or dieseling

Even though the key is off, the engine won't stop sputtering because the throttle plates are opened up enough to still pass a little fuel and air through it which in turn, continues to feed the cylinders just enough to cause it to sputter. This is why even factory cars with carburetors (mostly 80's and early 90's cars) had idle stop solenoids on them to completely close off the throttle plates when the key is switched-off, which completely shuts the fuel and air off, thus preventing run-on from happening.

With an idle stop solenoid, when you turn your key on, it gets power and clicks into position which pushes the throttle linkage to the normal "idle" position, but when the key is switched-off, it backs off and allows the throttle plates to completely close which won't allow any fuel or air to pass by to cause run-on. Its a simple installation to do. Both Edelbrock and Holley make them just for this.

Fuel injected cars don't have any Dieseling or run-on problems because the fuel is electronically pushed to the injectors via an electric fuel pump, and the injectors are electronically fired, so when you turn the key off, the fuel delivery completely stops. 

Carburetors aren't electric, so even when you shut off the ignition, the inertia of the engine still spinning before it comes to a final stop is enough to still suck-in a little fuel and air, and as long as it is still rotating just enough for a little fuel and air to still flow through that carb, it'll continue to feed a couple of the cylinders and cause them to fire which is the sputtering you get. Even though the ignition is off, hot carbon in the cylinders can continue to ignite that fuel.

Why does my engine still try to run after I shut it off?

There is another way to remedy this other than installing an idle stop solenoid which involves the vacuum advance and the ignition timing. Even though the timing has nothing to do with engine run-on, (because the key is turned off and "ignition timing" is no longer in play), timing DOES affect the engine's idle when it's running. You can experience this when setting your timing at an idle. If you advance the timing - the idle goes up. If you retard the timing - the idle goes down. 

You can manipulate the idle speed with the vacuum advance by hooking it up to manifold vacuum which will pull more timing (advance) at an idle, thus causing the idle to go up a couple of hundred RPM.

On Holley carburetors this is the vacuum port under the front bowl.

Why does my engine still try to run after I shut it off?

On Edelbrock carburetors it's the lower front vacuum port on the driver's side of the carb.

Once you hook it up this way, you can back down the idle speed screw a bit, which will drop the idle back down to a normal RPM because you just closed-off the throttle plates more than they were before. When you turn the key off now, the plates are closed-off more which will no longer allow enough fuel and air to pull through to cause any engine run-on or sputter.  

Some will say this adds too much overall timing to the engine when running around and driving, but that isn't true because when you are on the throttle, the manifold vacuum signal drops down to zero and puts you back to normal "mechanical" timing. Yes, you might be adding a bit more timing when idling, but once you romp on the throttle, your vacuum signal drops, so now the vacuum advance and additional timing isn't in play anymore. 

It's a remedy, but like all remedies, it may not be perfect. It works most of the time for most people, but the only way to find-out is to take about 3 minutes, a piece of 50 cent vacuum line and a screwdriver to see if it works for you or not.

If you don't want to mess with any of that, then there is still an easy option. In cars equipped with automatic transmissions, you can simply shut the engine off while idling in "Drive" and the load from the tranny will cause the engine to shut right off.

Manual transmission cars can be shut off while in gear (with the clutch pedal down) and then letting the pedal back up slowly when the key is turned off to load the engine a little bit, thus killing the engine with no run-on. Really though, the two best ways to fix this are either to install an idle stop solenoid, or use your vacuum advance hooked-up to manifold vacuum and then re-adjust your idle speed so it idles back down to a normal RPM and kills when you tun off the key.

Hey, if you liked this tech tip then please be sure to share it with your fellow gear head friends, and on your favorite car forums by copying the URL at the top of the page and sharing it with them. Thanks! 

spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer spacer